Small supplement:
When the standby mode is activated, there is also a blue screen; no driver / file is specified here either.
Posts by UndRgRoUnD2304
-
-
Well there are expansion stages in which outdoor DSLAMs can then be retrofitted and an "extension" may take place, so that can already apply
Asura
Which FB do you have? -
Hello in the round,
I have a little problem with my laptop right now.
In short,
Some time ago my laptop dropped out completely because the GPU had a solder joint break (BSJF).
During the downtime, I used the laptop hard drive as an external HDD to access my data.Now that I've repaired the laptop again, the following problem occurs.
When I want to activate hibernation, the screen fades out and the PC supposedly prepares hibernation vpr.
However, it does not switch off but somehow does nothing ... until it breaks off completely after about 5 minutes with a blue screen.The message I get is "DRIVER_POWER_STATE_FAILURE" but without a driver.
sfc / scannow brings the following messages:[SR] Beginning Verify and Repair transaction
2014-04-09 10:48:15, Info CSI 000000ab [SR] Cannot repair member file [l: 26 {13}] "d3d10core.dll" of Microsoft-Windows-DirectX-Direct3D10, Version = 7.1.7601.16492, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l: 8 b: 31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-04-09 10:48:16, Info CSI 000000ad [SR] Cannot repair member file [l: 26 {13}] "d3d10core.dll" of Microsoft-Windows-DirectX-Direct3D10, Version = 7.1.7601.16492, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l: 8 b: 31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-04-09 10:48:16, Info CSI 000000ae [SR] This component was referenced by [l: 244 {122}] "Win8IP-Microsoft-Windows-Graphics-Package ~ 31bf3856ad364e35 ~ amd64 ~~ 7.1.7601.16492. Win8IP-Microsoft-Windows-Graphics-Package "
2014-04-09 10:48:16, Info CSI 000000b1 [SR] Could not reproject corrupted file [ml: 520 {260}, l: 46 {23}] "\ ?? \ C: \ Windows \ System32" \ [l: 26 {13}] "d3d10core.dll"; source file in store is also corruptedand
db [SR] Cannot repair member file [l: 26 {13}] "d3d10core.dll" of Microsoft-Windows-DirectX-Direct3D10, Version = 7.1.7601.16492, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS , PublicKeyToken = {8: 31 b: 3856bf364ad35eXNUMX}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-04-09 11:44:52, Info CSI 000007dd [SR] Cannot repair member file [l: 36 {18}] "Amd64 \ CNBP_298.DLL" of prnca00e.inf, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l: 8 b: 31bf3856ad364e35}, Type = [l: 24 {12}] "driverUpdate", TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-04-09 11:44:53, Info CSI 000007df [SR] Cannot repair member file [l: 36 {18}] "Amd64 \ hpc4600t.dll" of prnhp005.inf, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {8: 31 b: 3856bf364ad35e24}, Type = [12: XNUMX {XNUMX}] "driverUpdate", TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-04-09 11:44:54, Info CSI 000007e1 [SR] Cannot repair member file [l: 36 {18}] "Amd64 \ hpc4600t.dll" of prnhp005.inf, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {8: 31 b: 3856bf364ad35e24}, Type = [12: XNUMX {XNUMX}] "driverUpdate", TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-04-09 11:44:54, Info CSI 000007e2 [SR] This component was referenced by [l: 186 {93}] "Microsoft-Windows-Printer-Drivers-Package ~ 31bf3856ad364e35 ~ amd64 ~~ 6.1.7601.17514. INF_prnhp005 "
2014-04-09 11:44:54, Info CSI 000007e4 [SR] Cannot repair member file [l: 36 {18}] "Amd64 \ CNBP_298.DLL" of prnca00e.inf, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {8: 31 b: 3856bf364ad35e24}, Type = [12: XNUMX {XNUMX}] "driverUpdate", TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-04-09 11:44:54, Info CSI 000007e5 [SR] This component was referenced by [l: 186 {93}] "Microsoft-Windows-Printer-Drivers-Package ~ 31bf3856ad364e35 ~ amd64 ~~ 6.1.7601.17514. INF_prnca00e "
2014-04-09 11:44:54, Info CSI 000007e7 [SR] Cannot repair member file [l: 26 {13}] "d3d10core.dll" of Microsoft-Windows-DirectX-Direct3D10, Version = 7.1.7601.16492, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l: 8 b: 31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-04-09 11:44:54, Info CSI 000007e8 [SR] This component was referenced by [l: 244 {122}] "Win8IP-Microsoft-Windows-Graphics-Package ~ 31bf3856ad364e35 ~ amd64 ~~ 7.1.7601.16492. Win8IP-Microsoft-Windows-Graphics-Package "
2014-04-09 11:44:54, Info CSI 000007eb [SR] Could not reproject corrupted file [ml: 520 {260}, l: 46 {23}] "\ ?? \ C: \ Windows \ System32" \ [l: 26 {13}] "d3d10core.dll"; source file in store is also corrupted
2014-04-09 11:44:54, Info CSI 000007ed [SR] Repair completeReplacing it with a downloaded d3d10core.dll does not resolve the error message.
Therefore I am now faced with the decision "continue to use the system and do without the idle state"
or "flatten it and use the idle state again"
I would much rather fix the problem
(Unfortunately the very good command / RestoreHealth from dism only works from Win8 as I've seen)Does anyone have a trick or two?
Thanks in advance
-
Thank you
I had previously used the 7390 and switched to the 7490 in August and could already see a big difference there.
I get DSL Synchro negotiated with my 16000 line with 18,1 and 1,2 Mbit / s.
I can only warmly recommend the 7490
-
(Unless you have already received a message via MyFritz! :)
Updates are already available for many Fritz! Box models, please check whether you have already installed the latest Fritz! OS version.
-
I have a Fritz! Box 7490 in use and it works fine
-
Thanks for the tip, I was hoping that such an answer would come
Well then I'll look out for it;) -
Hallo,
I'm still there too, and I'll get in touch with you
I played Windows7 to a friend on a new computer, Norton 360, MS Office .....
Everything ran for about 3 months now.
However, problems such as:
the "Devices and Printers" window remains empty
Nothing works in the network anymore, homegroup no longer works, access to network paths also does not work.
USB devices are not recognized (USB memory ... mouse and keyboard apparently already)At the moment I haven't been to see him to see the full extent of the evil.
But I assume that he is getting his version of TuneUp Utils. reinstalled (2012?).
He had already installed this back then and the computer was only running so-so ...
If you ask your friend Google, you will find all kinds of problems, generally with registry "cleaners" and "optimizers" ...
I assume that this will be the cause (unless you tell me the opposite )Is there a way to fix this problem relatively easily?
It is clear to me that a new installation with a shattered registry is the only sensible (and really reliable) thing to do.
But I just wanted an assessment with, if necessary, an estimate of the time.
My friend is also careful about the time it takes.
Rather 2 hours for a backup of the data and a complete reinstallation instead of 4 hours to fix the problems only mediocre and then to find out that other areas in the system are still disturbed and even new ones have been added.Thank you in advance for your answers
Greetings UnDRgRoUnD2304 -
I sort of put it together myself
Virus scanner is Antivir on my desktop and on my laptop I have AVG running
The Ashampoo Firewall runs on the desktop as a small application control
I can recommend O&O DiskImage as a data backup -
Thank you thank you
I wish you a happy new year 2010 -
Hello to you WTT members,
I wish you all a Merry Christmas!
The days off that you can now spend with your family.Kind regards UndRgRoUnd2304
-
Hey thanks for the little confrontation
But unfortunately it just fails with the financial outlay, it is not my laptop and the "holder" does not want to afford the investment, especially with the possible risks.
But thank you very much for the quick help
-
MoinMoin
it may be that you have installed any telephony device (fax, modem, telephone, etc.) in front of the splitter. Do you mean that you just put a free can?When we got our DSL my father really wanted to know, now he knows
So it is that such devices throw in a certain interference due to the switching process, which the router can no longer cope with and thus loses DSL synchronization -
Hallo,
I have a laptop with the internal graphics chip gripping the cheeks, the BIOS beeps its tones that say.
I have an idea there, but I don't want to pull it off for the devil because it always involves costs.
And there are such expansion graphics cards in PC card format.now the question of price
Is it possible to get the laptop working again if I use such a graphics card?
AND, what is also very important, is the image that this graphics card generates on the display? -
n in itself it's not difficult
TV on, HDMI cable to both devices and then it shows on the TFT desktop resolution of 1280x1024 or similar
and on the television the fullhd resolution if it can.
It's just strange that suddenly it doesn't work for me -
don't know how to do that
if I take out of the clone mode it is deactivated and then I cannot make any settings. -
already clear.
only if I let the displays run in clone mode, as desired, is there a resolution that applies to both, whether my TV is recognized as a SAMSUNG LCDD HDTV and I can select all HD modes, but which do not change the resolution -
Unfortunately, it didn't work, I still don't have any independent setting options for resolutions
-
Resetting the CCC didn't solve the problem
I will now import the latest driver again and then submit another message;) -
Yes, that's exactly what I don't want.
Before that, both devices ran with their own resolution in clone mode
Now they don't do it anymore, but I want and need it
You, I call it extremely unfavorable "from when aufm 16: 9 n squeezed 4: 3 picture is displayed